Before a spraying drone takes off, the operator needs to understand the paddock, the job and the conditions on the day. For a grower using this service for the first time, it helps to know what information will be needed and how the work is planned.
Preparation is not a formality. It decides whether a job goes ahead, how it is flown and what is applied. This guide walks through what a careful operator checks, how the planning tools on a DJI Agras drone support that work, what a typical job day looks like, and what to ask before you book.
What Needs to Be Checked Before Spraying?
Preparation starts with the crop, the target area and the application requirements. From there, the operator checks the site and the day.
The product and its label
Every chemical product has a label that sets the rules for how it can be applied. Labels are approved by the APVMA, and the states enforce how products are used. Some labels restrict application to piloted aircraft. In NSW, for example, a label that only allows fixed-wing application rules out spraying with a rotary drone. Before anything else, the operator confirms that the product you want applied can be used by drone.
The paddock and what surrounds it
The operator needs to know the boundaries, the crop stage and what sits nearby, such as neighbouring crops, waterways, homes and livestock. Site access matters too, along with obstacles like powerlines, poles, trees and fence lines. These details shape the flight path and decide where spraying should stop.
Weather on the day
Wind, rain and temperature determine whether spraying is suitable at all, and a good operator will postpone a job rather than push on in poor conditions. Some rules apply whatever the forecast. In Victoria, for example, drone spraying cannot be conducted before sunrise or after sunset, and each spray nozzle must have a leak-proof cut-off valve.
Spray drift is the main reason weather matters so much. In 2026, a Victorian drone spraying business was fined $15,000 after drift damaged about 4 hectares of land. Agriculture Victoria's investigation pointed to wind speed, release height, droplet size and the way the drone was flown. A careful operator treats wind as something to watch through the whole job, not a box to tick at the start.
Licences and permissions
CASA is the body responsible for drone operation standards across Australia, and the states add their own chemical requirements on top. Commercial operators generally need a remote pilot licence and a remotely piloted aircraft operator's certificate (ReOC), or must work under a business that holds one.
State rules then differ:
- Victoria: the pilot needs a chemical rating licence and the business needs an agricultural aircraft operator licence, both issued by Agriculture Victoria. The drone versions of these licences also depend on the CASA credentials above.
- NSW: the EPA requires both an RPA business licence and an RPA pilot licence.
- Queensland: anyone applying chemicals from a drone needs a state pilot chemical rating licence, even over their own land.
- Western Australia and South Australia: each has its own chemical handling and accreditation requirements. In WA, for example, the qualification is the Spraysafe course or equivalent training.
Growers do not need to memorise these rules, but they should expect the operator to know them. It is also fair to check: the NSW EPA keeps a public register of pesticide licences, and Agriculture Victoria will confirm on request whether a business holds an agricultural aircraft operator licence.
How you can help the operator prepare
A grower can speed up preparation by sharing a few things up front: a paddock map or boundaries, the crop and its growth stage, and the product to be applied with its label or permit details. It also helps to flag gates, powerlines, bores, dams and tanks, and any neighbouring crops, homes or livestock that need protecting. If conditions are likely to change on the day, agree early on who will be contacted and how a postponement will be handled. Tell the operator promptly about anything that changes between booking and the day, such as stock being moved into a paddock, new plantings next door or a tank being filled for household use.
How Do Spraying Drone Features Support Job Planning?
Depending on the DJI Agras model and operating setup, several functions support the preparation process. They help the operator plan and fly the job. They do not replace operator judgement or regulatory requirements.
Using the DJI Agras T100 as an example, the planning tools include:
- Field and route planning. The operator maps the area and sets the route before the aircraft flies. Mapping on the T100 is normally done with RTK for centimetre-level accuracy.
- Obstacle sensing. LiDAR, millimetre-wave radar and vision sensing can detect objects such as wires, poles, towers and trees. The system can also remember saved obstacle locations for later flights over the same field, and obstacles can be saved to a field with a single click.
- Terrain following. Downward sensing assists terrain following and altitude stabilisation, which matters on undulating country.
- Payload guidance. The DJI Agras app recommends a payload weight based on aircraft status and conditions. Maximum takeoff weight in Australia depends on aviation rules and the operator’s approvals, so it is worth asking what applies to their aircraft.
Used well, these features give the operator a clearer picture of the paddock before the aircraft leaves the ground. The limits matter as much, though. Sensing performance varies with light, rain, fog and the material of the obstacle, radar surfaces need to be kept clean, and wires must be marked. The operator confirms the site is safe; the aircraft does not do that for them.
Which of these functions are available depends on the model, firmware and setup, so ask the operator exactly what their aircraft can do and how they use it.
What Does Preparation Look Like on the Day?
On the day, preparation usually follows a set order. The details vary by operator, aircraft and property, but a well-run job looks similar to this:
- Confirm the job. The operator checks the paddock, crop, product and target area, along with any restrictions on the label or permit.
- Review the site. They look at access, obstacles, sensitive areas and neighbouring land, often with the grower on hand to point out anything that is not obvious.
- Check the weather. If wind, rain or temperature make spraying unsuitable, the job waits.
- Map and plan. The area is mapped, obstacles are marked, and the flight route is set.
- Prepare the aircraft. Batteries, sensors and nozzles are checked, and the product is mixed and loaded within the recommended payload.
- Brief and start. Anyone on site is told what is happening, and the operator begins the job.
None of this is meant to slow the job down. It is what allows the work to be done accurately and safely, and a good operator will be glad to talk a first-time customer through their own version of these steps.
Spraying Drone Examples from NSW Farms
Wheat spraying in NSW – September 2026
In September 2026, EE Group flew a single T100 on a fungicide job in a NSW wheat paddock, between stem elongation and heading. It launched from the headland track, so the aircraft never entered the crop, and a ute-mounted generator kept the batteries cycling. The standard workflow includes checking spray deposition on water-sensitive paper on the first load.
Canola spraying near Deniliquin – September 2026
Also in September 2026, a canola grower near Deniliquin used two T100s to treat 275 ha in one 10-hour day while the crop was in flower. On a separate occasion, a 147.95 ha paddock took 132 flights and used 4,418 L, or 29.9 L/ha, matching the planned rate. The drones logged these figures automatically.
What Happens After the Spraying Job?
Preparation does not end when the aircraft lands. Operators typically review what was applied and where, note any issues and clean the aircraft and spray system. Record-keeping requirements vary by state. In Victoria, for example, records of use must be made within 48 hours and kept for at least two years. A good operator can tell you what records they keep and give you the details of the application.
What Should Growers Ask Before Booking a Job?
A good operator will welcome questions, and the answers show how carefully they prepare. Before you book, ask:
- Which licences and certificates do you and your pilot hold for my state?
- Can the product I want applied be used by drone under its label or permit?
- What information do you need from me about the paddock, crop and chemical?
- How will you manage powerlines, trees, neighbours and sensitive areas?
- What weather conditions would make you postpone the job?
- Who is insured, and for what?
- What records will I receive after the job?
If you are weighing up a spraying drone for your own operation, explore the DJI Agriculture range or compare DJI Agras spraying drones to understand the available models and applications.
Official sources and further reading
For the current aviation and agricultural chemical requirements, refer to the relevant authority for your state or territory.
- Agriculture Victoria – Drone spraying requirements
- Agriculture Victoria – Drone spraying licences
- NSW EPA – Aerial application of pesticides
- Queensland Government – Pilot chemical rating licence
- WA DPIRD – Aerial pesticide application rules
- CASA – Get your remote pilot licence
- DJI – Agras T100 technical specifications
- Western District News – Victorian spray drift enforcement case