DJI Agras T100 agricultural drone flying over a flowering canola paddock in New South Wales
Agricultural drone field application / Australian canola

Australian Canola: A DJI Agras T100 Field Study

A New South Wales field record alongside an evidence-led review of canola growing regions, seasonal spray windows and the opportunities for drone operations.

NSW field images, September 2026NSW / VIC / SA researchPrepared October 2026
The study

Canola management and the role of the DJI Agras T100

Canola is an important winter broadacre crop across southern Australia. Its management programme changes substantially between establishment, flowering and ripening. This study examines where an agricultural spraying drone can fit into that programme, supported by field photographs from a DJI Agras T100 operation in New South Wales.

The study draws on a 40-slide research presentation dated 15 October 2026. The full production data, state breakdowns, pest and disease references, operating parameters and financial models are retained in the technical notes at the end of this page.

3.70m haAustralian canola areaPresentation estimate, 2025-26
7.68 MtAustralian canola productionPresentation estimate, 2025-26
9 mRecorded field swathNSW T100 imagery, Sep 2026
30 L/haRecorded spray volumeField record, not universal advice
01 / Field record

DJI Agras T100 over NSW canola at full flowering

In September 2026, the DJI Agras T100 was operated above a canola crop in full flower in NSW. The field photographs show the aircraft flying along the tramlines, with battery handling and charging equipment set up at the paddock edge.

Flowering canola paddock in New South Wales with existing tramlines visible
Flowering canola in NSW. Existing vehicle tramlines are visible across the crop.
01

Crop condition

A mature, flowering canola canopy, including emerging pods and branches that can be susceptible to disturbance.

02

Flight approach

The source describes a headland launch and travel along existing tramline direction. This avoids an additional vehicle pass through the crop.

03

Supporting equipment

The original photo series includes field preparation, an aircraft battery change and mobile power and charging equipment.

Field application configuration

DJI Agras T100 field configuration, NSW, September 2026
ParameterRecorded value
AircraftDJI Agras T100
Location and dateNSW, September 2026
Crop stageCanola in full flower
Flight swath9 m
Flight speed13.8 m/s
Flight height4 m above the canopy
Spray volume30 L/ha
Droplet size320 micrometres

These are the operating parameters recorded in the September 2026 field presentation. Actual applications must follow the current registered product label and applicable aircraft approvals.

DJI Agras T100 in the field. The NSW operation shows the T100 working above canola at full flowering, launched from the headland and flying along existing tramlines. The operation required no additional ground vehicle pass through the flowering crop.
02 / Industry context

Where Australian canola is grown

The report combines national crop statistics with a particular focus on NSW, Victoria and South Australia. These eastern regions are important because autumn-to-spring rainfall and paddock conditions shape the timing of in-crop applications.

Australian canola production

Australian canola production in million tonnes (Mt), 2020-21 to 2026-27. The final year is the 2026-27 forecast.

2020-21
4.5 Mt
2021-22
6.8 Mt
2022-23
8.3 Mt
2023-24
5.7 Mt
2024-25
6.4 Mt
2025-26
7.7 Mt
2026-27 forecast
7.3 Mt

Source: EE Group research presentation, slide 4; original sources cited as ABARES Australian Crop Report (2026).

Where Australian canola seed was exported

Export destination volumes in million tonnes, 2024-25 marketing year (total 5.4 Mt). The EU accounted for approximately two-thirds of the volume shown.

European Union
3.58 Mt
United Arab Emirates
0.62 Mt
Pakistan
0.47 Mt
Japan
0.30 Mt
Bangladesh
0.19 Mt
Other markets
0.24 Mt

Source: EE Group presentation, slide 4, using the export figures cited in the original research.

2025-26 area and production estimates as shown in source slide 5
StateArea (million ha)Production (Mt)Average yield (t/ha)Share of national area
Western Australia1.954.252.1853%
New South Wales0.951.601.6826%
Victoria0.541.252.3115%
South Australia0.250.552.207%
Other states0.010.03Not reportedLess than 1%
Australia total3.707.682.07100%

State shares follow the rounded figures in the source presentation. The 2026-27 production figure is a forecast.

Australian canola distribution by state for 2025-26, showing major production in Western Australia and the eastern states
National canola distribution reproduced from source slide 5.

New South Wales

Source map of canola growing areas in NSW highlighting Riverina, Central West and Murray regions

Riverina, Central West and Murray were the leading regional areas in the source breakdown. Sowing generally occurs in autumn and harvest runs from late spring.

Victoria

Source map of Victorian canola areas around Wimmera and Mallee

Wimmera and Mallee dominate the state area, while wetter western districts present different seasonal access constraints.

South Australia

Source map of South Australian canola regions including Eyre Peninsula and South East

Lower Eyre Peninsula and the South East are prominent in the source report, with conditions varying across districts.

The maps above are reproduced from the uploaded presentation. See source slides 5-8 in the research notes for detailed regional tables, crop calendars and source references.

03 / Whole-season timing

The application window changes with the crop

Winter canola progresses from establishment through flowering to pod fill and ripening. The type of work and its urgency change with the crop stage; there is no single operating setup that suits every treatment. A related example of weather-dependent crop protection is described in the NSW wheat spraying case study.

Illustrated canola growing stages from emergence and rosette to flowering, pod fill and maturity
Growth-stage diagram reproduced from the study presentation. Stages and dates are indicative for southern winter canola.
Southern Australian canola growth stages and indicative seasonal timing
Indicative stageTypical seasonCrop management focusPotential drone role
Emergence and seedlingApril to JuneEstablishment, early insects and mites, blackleg riskTargeted treatment or bait spreading when registered
Rosette and stem elongationMay to AugustWeed control, nitrogen and crop health monitoringSelected foliar crop-protection work subject to label
Bud and floweringJuly to SeptemberFlowering disease-risk assessment and canopy accessTime-critical applications where suitable and permitted
Pod fillSeptember to OctoberMonitoring aphids, diamondback moth and native budwormSite-specific pod-stage management
Ripening and harvestOctober to DecemberHarvest readiness, shattering risk and crop managementPre-harvest work only when current product permissions and harvest requirements allow
01

Flowering is time-sensitive

The study identifies early-to-mid flowering as a critical period for evaluating sclerotinia and upper canopy blackleg risk, with treatment choices based on disease risk and product labels.

02

Field access is variable

Wet soil can restrict access and mature stems are vulnerable to physical disturbance. Aerial access may offer additional scheduling flexibility.

03

Harvest planning begins early

Pre-harvest operations must account for crop maturity, seed moisture, export requirements and product-specific withholding periods.

Why the spray window matters. The report identifies a short 20-30% bloom window for sclerotinia management, often coinciding with winter-spring rainfall. The T100 provides aerial access to a tall, flowering canopy without an additional ground pass through the paddock.
04 / Crop health

Disease, pest and weed risks considered in the study

The source covers the major crop-protection decisions across the season. Each requires paddock monitoring, appropriate agronomic assessment and a currently registered treatment if chemical application is proposed. Further information on crop monitoring and site-specific application approaches is available in the precision agriculture section.

01

Disease

Blackleg, upper canopy infection and sclerotinia are important topics in the source report. Their timing, symptoms and disease pressure differ.

02

Insects and molluscs

The report examines early-season mites and slugs, aphids, diamondback moth and budworm during later crop stages.

03

Weeds and pre-harvest management

Fallow and post-emergent weed control, plus ripening-stage desiccation, are discussed separately because aerial label permissions differ.

Illustrative canola leaf symptoms associated with blackleg disease
Blackleg reference image included in the presentation; identification requires diagnosis.
Illustrative plant disease lesion associated with sclerotinia stem rot
Sclerotinia reference image from the source deck.
Illustrative leaf spot disease photo sourced from the presentation
Leaf-spot reference image; check source-caption species notes.
Diamondback moth caterpillar on brassica foliage in the source presentation
Diamondback moth reference image.
Native budworm caterpillar pictured in the source presentation
Native budworm reference image.
Wild radish flower illustrating a broadleaf weed in cropping systems
Wild radish and broadleaf weeds were covered in the source review.
Illustration of common flowering broadleaf weed in Australian canola systems
Additional broadleaf weed example from the source study.
Product and aviation requirements. The technical tables retain the October 2026 source information. Before any application, check current APVMA labels, CASA approvals and the relevant state rules.
05 / Application workflow

From field planning to a completed flight

A T100 application workflow comprises five stages: pre-flight checks, paddock mapping, route planning, parameter set-up and autonomous operation.

01

Assess conditions

Review weather, airspace, crop stage, people, powerlines, neighbouring operations and the product label.

02

Map the paddock

Establish field boundaries and identify obstacles, sensitive areas and required buffers.

03

Build the route

Plan routes in relation to tramlines, paddock shape, terrain and safe launch locations.

04

Check application setup

Verify the product-specific approved parameters and assess coverage before continuing.

05

Operate and document

Manage aircraft, chemical handling, batteries and flight records under applicable approvals.

DJI Agras T100 applications through the canola season

DJI Agras T100 applications across the canola season
Crop stageApplication contextSource reference
Early crop establishmentTargeted access after the autumn break for registered aerial applicationsWhole-season application programme
Flowering crop protectionTimely access during flowering disease-management windowsNSW field photographs, September 2026
Pod-stage monitoring and treatmentInsect monitoring and approved applications in a tall canopyCrop management programme
Pre-harvest managementRipening-stage desiccation and harvest planning where permittedPre-harvest cost and operating model
Pre-harvest management. The presentation compares drone desiccation and direct heading with windrowing and pick-up, including estimated operating costs and crop traffic effects. Treatment selection and timing depend on crop maturity, current APVMA labels, withholding periods and grain buyer requirements.
06 / Conclusion

What the NSW canola operation demonstrates

In the NSW field operation, the T100 flew above canola at full bloom from a headland setup, with no additional ground pass through the crop. The wider study identifies three particularly useful application periods: flowering disease control, pod-stage pest management and pre-harvest work. A related Australian crop spraying and contractor example is documented in the sugarcane drone spraying case study.

01

For growers

Evaluate each intended application by crop stage, paddock conditions, agronomic need and current product permissions.

02

For contractors

Plan capacity, refills, power supply, safe airspace separation and permitted chemical operations before the crop window opens.

03

Recording field performance

Record treated area, operating time, application coverage, service cost and crop outcomes alongside field photographs for future canola case studies.

Field takeaway. The September 2026 NSW photographs show how the T100 can be deployed over a mature flowering crop without another ground pass. The research adds the crop-stage, operating and cost context for using this approach through a canola season.
07 / Supporting research

Complete technical reference and source tables

Every substantive slide from the 40-page source presentation is retained below. Open any entry to review regional figures, disease and pest tables, application settings, operating comparisons, economics and original slide references.

These notes preserve the breadth of the original research without forcing the reader to scroll through 26 full-width tables before reaching the field story. The presentation contains 32 substantive research slides; the other slides are the cover, contents and section dividers.

Source data. Tables, estimates and application details below follow the EE Group presentation dated 15 October 2026. For field use, confirm current chemical labels and operating requirements.

Australian canola industry

1.1 Australian canola at a glance: area, production, valueSource slide 04

3.70 M ha

Canola area 2025-26 Second-largest crop by area; 2026-27 forecast 3.78 M ha

7.68 Mt

Production 2025-26 (2nd highest on record) Yield 2.07 t/ha; 5-year average ≈6.9 Mt

A$5.8 bn

Gross value of production 2025-26 ≈5.5% of total farm GVP; ≈11% of cropping; 3rd-largest crop

5.4 Mt

Seed exports 2024-25 marketing year ≈75–85% of the crop exported as seed; export value ≈A$4.9 bn

No. 2

World ranking, canola seed exports Behind Canada; ≈1/3 of world trade; EU takes 2/3 of exports

10,130

Canola-growing businesses 2024-25 NSW 3,385 / VIC 2,910 / WA 2,585 / SA 1,185

A$818–875/t

Canola price (Sep 2026, track) ≈2.2× the wheat price; every 1% of yield saved ≈ $20/ha

46%

GM canola share 2024 Eastern states still mainly TT / Clearfield; crush capacity ≈1.6 Mt

Sources: ABARES Australian Crop Report (Mar/Jun/Sep 2026); ABS Broadacre Crops 2024-25; ABARES Agricultural Commodities Sep 2026; USDA FAS (Apr 2026); OGTR (Dec 2025); Grain Central (Nov 2025 / Sep 2026). 2026-27 is a forecast; GVP and export value pro-rated from ABARES.

1.2 Where canola is grown: the canola belt and state sharesSource slide 05
Original data: source slide 5
StateArea (M ha)Prod. (Mt)Yield (t/ha)Area shareProd. shareGrowers
WA1.954.252.1853%55%2,585
NSW0.951.601.6826%21%3,385
VIC0.541.252.3115%16%2,910
SA0.250.552.207%7%1,185
QLD / TAS0.010.03—<1%<1%65
Australia3.707.682.07100%100%10,130

Canola is the core break crop in the wheat rotation

  • It overlaps the wheat belt but concentrates on the southern slopes and plains with 350–600 mm of winter-dominant rain: the NSW Riverina / Central West / Murray, the VIC Wimmera / Mallee / northern irrigation districts, and SA's Lower Eyre Peninsula / South East. Summer-dominant northern NSW grows almost none.
  • The three eastern states (NSW + VIC + SA) total 1.74 M ha — 47% of national area and 44% of production; WA alone grows more than half.
  • Typical rotation: wheat – canola – barley (– pulse); canola one year in 3–4, sown ≥500 m from last year's canola stubble (blackleg management).
  • 2026-27 outlook: good winter rain in VIC/SA, production +14–15%; autumn drought in northern and western NSW, area −25%.

Sources: ABARES Australian Crop Report Mar/Jun 2026 (2025-26 estimates); ABS Broadacre Crops 2024-25 (grower numbers); ABARES Sep 2026 (2026-27 forecast); CropLife 2026 blackleg management strategy.

1.3 New South Wales: largest eastern producer, 26% of national areaSource slide 06

0.95 M ha

Area sown 2025-26

1.60 Mt

Production 2025-26

1.68 t/ha

Yield (5-yr avg ≈1.9)

3,385

Canola growers

Original data: source slide 6
Region (SA4)Area (ha)ShareYield t/haKey districts
Riverina311,24429%1.55Wagga, Griffith, Narrandera, Temora
Central West285,23726%1.29West Wyalong, Condobolin, Forbes, Cowra
Murray216,00620%1.95Corowa, Deniliquin, Finley
Far West & Orana166,49815%1.75Narromine, Dubbo, Nyngan
New England & NW60,3936%3.84Gunnedah, Quirindi (Liverpool Plains)
Capital Region41,9794%2.06Young, Yass

Climate and soils: Canola concentrates on the south-west slopes and Riverina (Wagga 572 mm, winter-dominant; red-brown earths and red clay loams) and the Murray / Riverina irrigation districts; Liverpool Plains black soils give the highest yields (3.8 t/ha). The summer-rainfall north-west plains grow very little.

Sowing and harvest: Sown mid-April to mid-May (hybrids and slower types first, TT conventionals later); optimum start of flowering at Wagga 31 Jul – 1 Sep; windrowed or desiccated mid-Oct to early Nov; harvested late Oct to early Dec.

Main varieties: TT: PY429T, Hyola 350TT, ATR Bonito / Wahoo; Clearfield: 44Y90 CL, Hyola 580CT; RR / TruFlex: Hyola 600RR, 45Y25 RR, InVigor LR 3540P.

Industry standing: 2024-25 canola GVP A$1.37 bn; Riverina + Central West + Murray account for 75% of the state; record crop of 2.11 Mt in 2021-22.

Sources: ABARES Jun/Sep 2026; ABS Broadacre Crops 2024-25 (SA2 area, heat map); GRDC canola phenology research (2021); NSW DPI Winter Crop Variety Sowing Guide 2025.

1.4 Victoria: Wimmera + Mallee grow 55% of the state cropSource slide 07

0.54 M ha

Area sown 2025-26

1.25 Mt

Production 2025-26

2.31 t/ha

Yield (5-yr avg ≈2.2)

2,910

Canola growers

Original data: source slide 7
Region (SA4)Area (ha)ShareYield t/haKey districts
North West (Mallee + Wimmera)355,67255%1.93Buloke, Yarriambiack, Nhill, Ararat, Horsham
Shepparton (Northern Country)101,56816%2.62Moira (3.4 t/ha), Numurkah
Bendigo (Loddon)58,4169%2.07Loddon
Ballarat48,1407%2.72Beaufort, Golden Plains
Warrnambool & SW39,9216%2.64Western District, high rainfall
Hume / Geelong44,5157%2.2–3.1Wangaratta, Geelong

Climate and soils: The Wimmera (Horsham 373 mm) grey cracking clays and the Mallee calcareous sandy loams are the main production zone; northern irrigation districts 400–500 mm; the Western District / Ballarat (550–750 mm) yields 3–4 t/ha but is prone to waterlogging.

Sowing and harvest: Sown mid-April to mid-May (April start best); optimum start of flowering at Horsham 18 Jul – 25 Aug; windrowed late Oct to mid-Nov; harvest early Nov (Mallee), mid-Nov to Dec (Wimmera / north), Dec–Jan (Western District).

Main varieties: Mallee / Wimmera: quick–mid TT hybrids (Hyola 350TT, PY422T, InVigor T 3510), Clearfield 44Y94 CL, TruFlex InVigor R 4022P; slower hybrids and winter types in the high-rainfall zone.

Industry standing: Third-largest crop after wheat and barley; 2024-25 GVP A$1.04 bn; 2025-26 crop the fourth largest on record; lentils now compete with canola for break-crop area.

Sources: ABARES Mar/Sep 2026; ABS Broadacre Crops 2024-25 (heat map); BCG start-of-flowering research; Agriculture Victoria; GRDC (2018) canola agronomy research.

1.5 South Australia: Lower Eyre Peninsula 35%, production recoveringSource slide 08

0.25 M ha

Area sown 2025-26

0.55 Mt

Production 2025-26

2.20 t/ha

Yield (5-yr avg ≈2.1)

1,185

Canola growers

Original data: source slide 8
Region (PIRSA 2025-26)Area (ha)ShareYield t/haKey districts
Lower Eyre Peninsula80,00035%2.60Cummins, Port Lincoln
Upper / Lower South East57,15025%2.3–3.7Bordertown, Naracoorte, Millicent
Mid / Upper / Lower North42,00019%1.7–2.0Clare, Jamestown, Balaklava
Yorke Peninsula11,5005%2.10Kadina, Maitland
Eastern / Western Eyre13,0006%0.8–1.3Cleve, Kimba
Murray Mallee & other22,50010%0.3–1.6Lameroo, Kangaroo Is., Fleurieu

Climate and soils: Mediterranean winter rainfall; the Lower EP (400–500 mm, calcareous sandy loams) is the most reliable zone; the South East (450–650 mm, sandy duplex soils) yields the most (3.7 t/ha); Mid North red-brown earths; the Murray Mallee (250–350 mm sands) is marginal.

Sowing and harvest: Sown late April to May (dry-sown on much of the EP); target start of flowering late Jul to late Aug; windrowed mid-Oct to early Nov; harvested early Nov (EP / Mid North) through December (South East).

Main varieties: EP still mostly TT; RR / TruFlex hybrids have expanded since GM was allowed in 2020; Kangaroo Island remains non-GM.

Industry standing: Drought year 2024-25 produced only 0.45 Mt (A$315 m); 2025-26 recovered to 0.55 Mt, 2026-27 forecast 0.63 Mt (+15%); record 0.78 Mt / A$581 m in 2022-23.

Sources: ABARES Mar/Sep 2026; PIRSA Crop & Pasture Report (Jan/May 2026); ABS Broadacre Crops 2024-25 (heat map by area sown, a drought year).

1.6 Canola growth cycle (southern winter canola, sown late Apr – May)Source slide 09
Original data: source slide 9
StageBBCHDays after sowingKey managementDrone-relevant jobs
Emergence – seedlingBBCH 10–140–30Starter fertiliser, pre-emergent herbicide, seed treatment (blackleg / mites); RLEM and slug controlInsecticide; bait spreading
RosetteBBCH 15–1930–80Foliar blackleg fungicide at 4–6 leaf; post-emergent herbicide (TT / CL / RR system); urea topdressingFungicide; grass herbicide (clethodim); urea spreading
Stem elongation – budBBCH 30–5980–105Last nitrogen; aphid monitoring (GPA / cabbage aphid)Insecticide; urea spreading
FloweringBBCH 60–69105–140Sclerotinia / UCI fungicide at 20–30% bloom (critical); no application after 50% bloom; aphids / DBM★ Fungicide, insecticide (crop at full height; worst wheel damage)
Pod fill – ripeningBBCH 70–89140–190Native budworm / DBM / Rutherglen bug; windrow at 60–80% seed colour change or desiccate at 70% pod yellowing★ Insecticide, desiccant (diquat), pre-harvest weed control

Sources: NSW DPI Procrop Canola growth & development; GRDC Canola GrowNotes; CropLife 2026 fungicide resistance management strategy; DPIRD. Diagram is stylised.

1.7 The mechanised canola season and where the drone fitsSource slide 10

01 Fallow & pre-sowing

No-till fallow, summer weed knockdown, paddock selection ≥500 m from last year's canola stubble; 36 m self-propelled boom for knockdowns

02 Precision sowing

Air seeder at 1.5–3 kg/ha, 2–3 cm deep, with starter fertiliser; pre-emergent herbicide (trifluralin / propyzamide) incorporated by sowing; seed dressing for blackleg and mites

03 In-crop management

Boom spray / fixed-wing applications and spreader topdressing; flowering fungicide, pod-stage insecticide and after-rain jobs taken over by the DJI T100

04 Windrowing / desiccation

Windrow at 60–80% seed colour change, or desiccate with diquat by drone at 70% pod yellowing and direct head (PodGuard shatter-tolerant types can be direct headed)

05 Harvest & export

12–13 m front picking up windrows or direct heading at 8% seed moisture; GM / non-GM segregated; 75–85% exported as seed (EU takes 2/3)

Where the drone fits: Canola is Australia's highest-value broadacre crop (≈$820/t, 2.2× wheat) and the hardest to get ground gear into — at flowering it stands 1–1.5 m with interlocking branches, so every ground pass after stem elongation snaps flowering branches and knocks pods off.

  • The drone takes on four key passes: 4–6 leaf blackleg fungicide / seedling insecticide, the 20–30% bloom sclerotinia fungicide (a 7–10 day window), pod-stage DBM / budworm insecticide, and pre-harvest desiccation (replacing windrowing, $30–40/ha).
  • Typical combination: self-propelled boom (pre-sowing / seedling stage on dry ground) + T100 (post-flowering, wet paddocks, small or awkward paddocks, desiccation) + fixed-wing (very large emergency jobs).

Photos: 01/02/05 Wikimedia Commons (CSIRO ScienceImage 4277 wheat stubble fallow NSW, CC BY 3.0; Challenger tractor seed drilling, CC BY 2.0; rapeseed harvest, Smaack, CC BY-SA 4.0); 03/04 EE Group field photos.

Whole-season operating challenges

2.1 Canola growth stages and the farm calendarSource slide 12
Original data: source slide 12
Item / monthDecJanFebMarAprMayJunJulAugSepOctNov
Growth stageHarvest / summer fallowSummer fallowSummer fallowFallow / sowing prepSowing (from mid-Apr)Sowing / emergence – 2 leafRosette 4–8 leafRosette – stem elongation / budElongation – first flower – 20% bloomFull bloom (50–80%) – poddingPod fill – colour changeWindrow / desiccate / harvest
Fertiliser///Soil testingMAP/DAP at sowing/Urea topdress (moist soil)Main N (rosette – bud)////
Weed controlFallow knockdown (glyphosate + 2,4-D)Fallow knockdown / double-knockFallow knockdownPre-sowing knockdownPre-emergent (trifluralin / propyzamide)/TT: atrazine; CL: Intervix; RR: glyphosate; clethodimLast post-emergent (before bud)//Pre-harvest weed control (glyphosate, registered product only)/
Pests & disease//Mouse monitoringGreen-bridge control / snail baitsSeed dressing (blackleg / mites); bare-earth mite sprayRLEM / blue oat mite / lucerne flea / slugs; GPA (TuYV)Blackleg fungicide at 4–6 leafAphid monitoringSclerotinia / UCI fungicide at 20–30% bloomOptional 2nd spray at 50% bloom; DBM / aphidsNative budworm / DBM / Rutherglen bug/
Field operationsHarvest / stubble management///Sowing (no-till)Sowing////Windrowing (from mid-Oct) / desiccationHarvest (pick-up / direct heading)
Typical rainfallSummer stormsSummer rainSummer rainBefore the autumn breakAutumn break, sowing rainWinter rainWinter rainWinter rain (wettest)Winter–spring rainSpring rainSpring rain easingDry

Note: based on dryland winter canola in the south (Riverina / VIC / SA) sown mid-April to mid-May and harvested late October to December; optimum start of flowering late Jul – early Sep at Wagga, mid-Jul – late Aug at Horsham. Core drone windows: the flowering fungicide in Aug–Sep (20–30% bloom, a 7–10 day window, nothing after 50% bloom), pod-stage insecticide in Sep–Oct and desiccation in Oct–Nov — when the crop is tallest, the branches most brittle and a ground pass costs the most.

Sources: NSW DPI Procrop; GRDC Canola GrowNotes; CropLife 2026 RMS; cesar PestFacts; PIRSA; BCG.

2.2 Where the ag drone fits across the canola seasonSource slide 13
Interpretation: any projected benefits, costs, comparisons, service rates or market sizes in this subsection are research examples or EE Group assumptions, not independently measured results from the NSW photographed paddock.
Original data: source slide 13
StageSummer fallow / (Dec–Mar)Pre-sowing / sowing / (Apr–May)Seedling – rosette / (May–Jul)Bud – flowering / (Aug–Sep)Pod fill / (Sep–Oct)Ripening / pre-harvest / (Oct–Nov)
Job opportunitiesFallow weed knockdown / (glyphosate / 2,4-D)Pre-emergent herbicide (IBS) / starter fertiliser, seed dressingRLEM / lucerne flea / blackleg fungicide at 4–6 leaf / clethodim grass control / GPA aphidsSclerotinia at 20–30% bloom / upper canopy blackleg / aphids (cabbage aphid / GPA)Diamondback moth, native budworm / Rutherglen bugDesiccation (diquat) / pre-harvest weed control / snail baits
Drone suitabilityYes (top-ups / spot spraying) / booms still do the big areasNot suitable / (needs incorporation / the seeder)Yes / clethodim / Affirm / Prosaro labels allow aerial; atrazine / Intervix do not★ Core scenario ★ / crop 1–1.5 m tall, brittle flowering branches, / only a 7–10 day window★ Core scenario ★ / pods shed easily; worst wheel damage★ Core scenario ★ / replaces windrowing ($30–50/ha) / drone desiccation $30–40/ha
Estimated share of drone work5%0%15%35%15%30%
Main bottleneckBoom is fast and cheap at $8–13/haPre-emergent labels prohibit aerial useAtrazine (TT) and Intervix (Clearfield) labels prohibit aerial use; only clethodim, insecticide and fungicide jobsAerial label minimum ≥20 L/ha (Prosaro recommends 30); nothing after 50% bloom; bee safetyWithholding periods before harvest (counted to windrowing)Diquat aerial label 30–60 L/ha; APVMA June 2026 decision (231 g/ha cap, 14-day WHP) — follow the new label

Takeaway: canola is the broadacre crop where the drone earns the most — the flowering fungicide, the pod-stage insecticide and pre-harvest desiccation all fall when the crop is tallest, most brittle and the paddock wettest; every ground pass drives over a $1,600/ha crop, and desiccation directly replaces a $30–50/ha windrowing contract. Shares are estimates based on application windows and ground-access limits; calibrate against actual job data.

2.3 Strengths and weaknesses of the ag drone on canolaSource slide 14
Interpretation: any projected benefits, costs, comparisons, service rates or market sizes in this subsection are research examples or EE Group assumptions, not independently measured results from the NSW photographed paddock.
Original data: source slide 14
DimensionKey strengthsKey weaknesses
Work rateTwo T100s (two pilots + one mixer): 9 m swath, 13.8 m/s, 30 L/ha, 44–52 ha/h in practice, 360–520 ha per shift — on a par with one self-propelled boom (≈500 ha/day); / 3,000–4,000 ha covered inside the 7–10 day flowering windowBattery and payload limited: 100 L tank (≈3.3 ha per sortie at 30 L/ha), landing to refill every 6–7 minutes; needs a generator and a six-battery / two-charger rotation; / if desiccation is flown at the 60 L/ha label maximum, output halves
Terrain and accessNot limited by soil moisture or crop height: flying 1–2 hours after rain; / no snapped flowering branches, no shed pods, no wheel tracks or compaction; / suits small, irregular and irrigation-bay paddocksOn large, flat, dry paddocks the boom is still cheaper per hectare; / fixed-wing aircraft do more per sortie
Application qualityRTK centimetre positioning, no overlap or misses; / rotor downwash carries the spray into the flowering canopy and onto the main stem — exactly the deposition sclerotinia and UCI blackleg control needLabels require MEDIUM droplets, ≥20 L/ha and 60–180 m water-body buffers for aerial use; / no advantage for high-volume (≥100 L/ha) pod sealants or ground-level coverage
Cost–benefitThe real advantage is the losses avoided: flowering wheel damage (1–3% ≈ $16–48/ha per pass), a missed sclerotinia window (≈$320/ha in a high-pressure year), desiccation replacing windrowing ($30–50/ha saved plus 5–10 days of windrowing-timing losses); / service price $15–25/ha ($30–40/ha for desiccation), the same as fixed-wing; two T100s ≈ A$100,000Farms under 2,000 ha take more than a year to pay back a purchase (break-even ≈750 ha/year); / labour: one licensed pilot + one mixer
Compliance and safetyOperator separated from the chemical; Prosaro, Aviator Xpro, Affirm, clethodim and diquat all carry aerial directions; / the NSW EPA RPA pesticide licence framework is in placeNeeds CASA RePL (class rating) + ReOC and state chemical licences; VIC daylight only; / manned ag aircraft are busy over canola at flowering — in Sept 2026 the AAAA warned of near misses between drones and aircraft over canola; CTAF broadcasts and airspace coordination are mandatory

Sources: DJI T100 specifications; Bayer Prosaro / Aviator labels; Syngenta Reglone label; AAAA / AgAir Update (Sep 2026); GRDC; Agriculture Victoria RPA chemical-use rules.

2.4 Bottleneck 1: ground gear can't get on after rain at floweringSource slide 15

T100 working tramlines in a NSW canola crop at full bloom (Sep 2026, EE Group video frame)

Problem: the sclerotinia window coincides with winter–spring rain

  • Sclerotinia infects when the canopy stays wet for 48 hours with ≥5 mm of rain during flowering — the very days the spray is needed are the days the boom can't get on
  • 20–30% bloom (14–20 flowers on the main stem) is the only economic window, just 7–10 days; applications after 50% bloom are prohibited (MRL / withholding)
  • In the 2021/2022 La Niña years large areas of Riverina and Western District canola were waterlogged — aircraft were booked out and booms bogged; in 2023, 42% of surveyed canola paddocks in central/southern NSW had sclerotinia

Consequence: a missed window is lost yield

  • Sclerotinia: up to 24% yield loss recorded in VIC and >20% in WA; WA industry loss >A$59 m in 2013; Bayer's 25 trials averaged +20% yield from a flowering spray
  • Upper canopy blackleg: up to 30% loss plus 20% from pod infection; the 30% bloom spray is the only timing
  • Native budworm: each larva per 10 sweeps at podding ≈ 6 kg/ha; in a bad DBM year a third of WA canola can be affected
  • Windrowing too early: up to 100 kg/ha lost per day ($50/ha/day)

Drone solution: fly as soon as the rain stops, touch nothing

≤ 2 hours

Time to be airborne after rain stops (pilot + mixing-station model)

0 passes

Ground passes through the crop launch from headlands / hard standing

22–26 ha/h

Actual T100 work rate per unit (100 L full load, 30 L/ha)

180–260 ha

Per unit per day two units cover 3,000+ ha in 7 days

$245/ha

Return from aerial Prosaro at Cowra NSW (35 L/ha, 30% bloom)

Case: Bayer's Cowra NSW trial applied Prosaro at 450 mL/ha by air (35 L/ha) at 30% bloom — yield 2.18 → 2.75 t/ha, return $245/ha; Walbundrie NSW 0.90 → 1.55 t/ha, return $289/ha; Moonyoonooka WA 2016, one (50% bloom) / two sprays returned a net $118 / $148/ha.

Sources: Agriculture Victoria; DPIRD sclerotinia management; GRDC Update (2014/2017/2024, Lindbeck); Bayer Prosaro canola guide; cesar; GRDC GroundCover.

2.5 Bottleneck 2: wheel damage at flowering and ripeningSource slide 16
Interpretation: any projected benefits, costs, comparisons, service rates or market sizes in this subsection are research examples or EE Group assumptions, not independently measured results from the NSW photographed paddock.

One pass of a 36 m boom through canola at full bloom

◄──────────────── 36 m swath ────────────────►

Wheel tracks 2.1–2.8% plus the snapped / flattened flowering branches either side (pale bands): whole-paddock loss is higher than in wheat

Original data: source slide 16
MeasureValueSource
Wheel-track share, 36 m boom2.1–2.8% (0.38–0.50 m tyres)Geometry; Grainews measured 3%
Wheel-track share, 24 m boom3.2–4.2%As above
Yield loss on heavily trafficked plots (CTF)5–30%BCG low-rainfall CTF project
Loss inside the track at flowering≈100% (snapped branches don't set pods) + damage either sideEE Group observations; Purdue (no compensation after flowering)
Loss inside the track at ripening (desiccation / pre-harvest)≈100% + shed pods / shatteringGRDC shattering research: 10 pods/m² ≈ 10 kg/ha
Compaction loss (soil)14–35%, persisting for seasons on sandsGRDC; DPIRD
Whole-paddock loss per ground pass after flowering1–3% ≈ $16–48/ha (2 t/ha × $800/t)EE Group estimate
Whole-paddock loss per ground pass at desiccation / pre-harvest2–4% ≈ $32–64/haEE Group estimate (tracks + shattering)

The "true cost" of one sclerotinia fungicide pass at 30% bloom (2 t/ha, $800/t, crop worth $1,600/ha)

Self-propelled boom

$8–13/ha application + $16–48/ha wheel damage + long-term compaction = $24–61/ha or more

Fixed-wing aircraft

$20–25/ha application no wheel damage needs an airstrip, a minimum area, and queues nationwide at flowering = $20–25/ha + delay risk

DJI T100

$15–25/ha application no wheel damage, no compaction flies straight after rain, any paddock size = $15–25/ha

Note: wheel-damage losses are estimates based on CTF research, overseas wheel-track trials and boom geometry; there is no published Australian trial of boom traffic through flowering canola.

Drone application programme

3.1 Key canola diseases: foliar-controllable, drone-suitableSource slide 18
Original data: source slide 18
GroupDiseaseField identificationConditions / timingYield lossDrone suitability
FungalBlackleg crown canker / (Leptosphaeria maculans)Blackened crown when cut at maturity; grey-white leaf lesions with black pycnidia on seedlingsStubble-borne; spores released ≈3 weeks after the break; cotyledon – 4 leaf most susceptible; mid-May to early Aug>90% loss uncontrolled; yield lost once >30% of the crown is discoloured★★ Foliar fungicide at 4–6 leaf (Prosaro / Aviator / Miravis Star)
Upper canopy infection (UCI)Lesions on flowers, stems, branches and pods; blackened pith when cut; crown cleanEarly flowering (Jun–Jul) + rain during floweringUp to 30%; pod infection costs another 20%★★★ 30% bloom, combined with the sclerotinia spray
Sclerotinia stem rotPale brown → bleached white lesions on the main stem; premature ripening, shredded stems, black sclerotia ("rat droppings") insideInfected petals; canopy wet >48 h, ≥5 mm rain; 10–22 °C; earliest-flowering paddocks worstVIC 24%, WA >20%; WA 2013 >A$59 m★★★ Core: 20–30% bloom (14–20 flowers on the main stem); not after 50%
Alternaria black spotConcentric dark brown spots with yellow halo on leaves and pods; pod infection → shrivelled seed, early shatteringWarm, wet springs; susceptible after full bloomUsually minor; shattering the main effect△ Aviator Xpro 650 mL/ha; rarely warranted
White leaf spotGrey-white to pale brown spots ≤1 cm, granular surface, no pycnidiaLong wet autumn–winterRarely reduces yield△ Miravis Star registered
OomyceteDowny mildewYellow blotches on the upper leaf, white mould underneathCool and wet, mainly at rosetteUsually minor✕ Rarely warranted
Soil-borneClubrootRoot galls, white → grey-brown soft rotWarm, spread in irrigation water; TAS and parts of NSWSerious in vegetable brassicas✕ Rotation ≥5 years, no chemical

Symptoms

Sources: Agriculture Victoria canola diseases; DPIRD sclerotinia management; GRDC Blackleg Management Guide 2025; GRDC Update (2019/2021); CropLife 2026 RMS. Photos: Wikimedia Commons (Alternaria / downy mildew / clubroot on other brassicas; white leaf spot is an indicative leaf-spot image).

3.2 Key canola insect pests and molluscsSource slide 19
Original data: source slide 19
GroupPestDamage and identificationPeak timingControl thresholdDrone suitability
Mites / springtailsRedlegged earth mite / blue oat mite / lucerne fleaSilvering of cotyledons and leaves (mites) or windows (lucerne flea); canola seedlings are the most sensitive crop — "more than 10% of canola failures are mite-related"2–3 weeks after the autumn breakCotyledon: ≥20% of plants damaged; 1 true leaf: 10 mites/plant★ Bare-earth or post-emergent spray; booms can also do it
SuckingGreen peach aphid (GPA) / cabbage aphid / turnip aphidGPA spreads turnip yellows virus in autumn–winter; cabbage aphid (grey-mealy) and turnip aphid colonise flowering heads and pods in springAutumn–winter (virus); bud – podding (direct damage)≥20% of plants (stems ≥25 mm) infested; sample twice weekly from flowering to podding★★ Bud – flowering (sulfoxaflor / afidopyropen)
ChewingDiamondback moth (DBM)Green larvae ≤12 mm that wriggle and drop when disturbed; windowed leaves, buds and young pods eatenSpring, Aug–Oct; outbreaks in dry warm springsPre-flowering >10 per 10 sweeps; flowering – podding >50; podding >100★★★ Podding, crop at full height (Affirm aerial ≥20 L/ha; avoid SPs / OPs)
Native budworm / (Helicoverpa punctigera)Larvae bore into pods and eat the seed; worst losses at ripeningFlowering – podding, Sep–OctET ≈ 4 per 10 sweeps (at $450/t); each larva ≈ 6 kg/ha★★★ Podding; mind the WHP before windrowing
CutwormSeedlings cut off at ground level, bare patchesAutumn, seedling stage2–3 larvae/m²★ Spot spray at dusk
BugsRutherglen bug≥5 nymphs per seedling can kill plants; sucking seed at podding lowers oil contentSeedling; podding – windrowing5 per plant at seedling; 20 heads at 5–10 points at podding★★ Podding
MolluscsSlugs / snailsShredded cotyledons and lost seedlings; snails contaminate grain at harvestAutumn – spring (>450 mm zones)Black keeled slug ≥1/m²; white snail 5/m²★★ Bait spreading (5–16 kg/ha)

Photos

Sources: DPIRD canola pest thresholds; cesar Australia (RLEM thresholds, DBM, budworm ETs); AOF Canola Manual ch. 11; GRDC GroundCover (2024/25). Photos: Wikimedia Commons.

3.3 Weeds, herbicides and desiccation: what the drone can take onSource slide 20
Historical source material: chemical names, rates, withholding periods, flight settings and licensing statements reproduce the supplied October 2026 presentation. They are not instructions or confirmation of current legal permissions. Check the current registered label, APVMA decisions, CASA approvals and state requirements before any operation.
Original data: source slide 20
JobTimingRepresentative chemistry (active / example product / label rate)TargetAerial use on labelDrone suitability
Summer fallow knockdownDec–MarGlyphosate 570 g/L 0.95–1.25 L/ha + 2,4-D amine ≤1.0 L/ha; paraquat double-knockFleabane, sowthistle, melonsPermitted (COARSE–VC, 3–15 km/h)★★ Timeliness 2–3 weeks after rain
Pre-emergent (IBS)At sowingTrifluralin 480 g/L 1.7 L/ha; propyzamide; Group 15Ryegrass, wild oatsNot permitted (needs incorporation)✕
Post-emergent (by system)4–6 leaf to before budTT: atrazine 900 WG 0.5–1.1 kg/ha + crop oil; Clearfield: Intervix (imazamox + imazapyr); RR / TruFlex: Roundup Ready 0.9–1.3 kg/ha up to 6 leaf / first flowerWild radish, turnip weed, mustards, grassesAtrazine: "do not apply by air to TT canola"; Intervix: ground only; RR glyphosate: label to confirm✕ Broadleaf systems largely unsuitable
Post-emergent grass2 leaf to before budClethodim 240 g/L 150–250 mL/ha + adjuvant (once per season)Ryegrass, wild oats, volunteer cerealsPermitted, aerial 20–30 L/ha★★ 30 L/ha, 500 µm
Pre-harvest desiccation70% of pods yellow / (≈70% seed colour change)Diquat 200 g/L (Reglone) 1.5–3 L/ha + wetter; 4-day WHP; direct head 4–7 days later [APVMA June 2026 decision: ≤231 g/ha, 14-day WHP — follow the new label]Even ripening, replaces windrowingPermitted, aerial 30–60 L/ha; avoid inversions★★★ Core: $30–40/ha instead of $30–50/ha windrowing, with no ground pass
Pre-harvest weed control≥20% seed colour changeGlyphosate (Weedmaster DST only, weed-control use); MRL: AU 20 / EU 10 / China 2 mg/kgRyegrass seed setPermitted (label)★ Buyer sign-off needed; care in non-GM / EU markets

Key weeds

Desiccation vs windrowing: windrowing contracts run $30–50/ha; windrowing too early costs up to 100 kg/ha per day ($50/ha/day), with NSW trials losing up to 32–55%; diquat at ≈70% colour change brings harvest forward ≈5 days and direct heading costs $37/ha less than picking up a windrow; desiccation also cuts ryegrass seed set by 65–87%. Where the drone sits: it doesn't compete with pre-emergents or TT / CL broadleaf herbicides; it takes on clethodim grass control, fallow knockdown top-ups and pre-harvest desiccation — desiccation is the single largest drone market on canola. Parameters (herbicide / desiccant): 8 m swath, 9 m/s, 3.5 m height, 30 L/ha, 500 µm droplets (diquat is a contact herbicide and needs near-full coverage; 30 L/ha is the label minimum for aerial use).

Sources: Syngenta Reglone label; APVMA paraquat / diquat final decision (23 Jun 2026); GRDC Canola GrowNote desiccation chapter; GRDC direct-heading canola fact sheet; Grain Central; CBH glyphosate residue guidance; APVMA atrazine / clethodim / Intervix labels.

3.4 Drone chemical program for canola diseases and pests (label rates)Source slide 21
Historical source material: chemical names, rates, withholding periods, flight settings and licensing statements reproduce the supplied October 2026 presentation. They are not instructions or confirmation of current legal permissions. Check the current registered label, APVMA decisions, CASA approvals and state requirements before any operation.
Original data: source slide 21
StageTargetTriggerPassesRecommended chemistry and rate (per ha)TimingParametersUnit
Seedling / (May–Jun)RLEM / blue oat mite / lucerne fleaCotyledon ≥20% of plants damaged; 1 true leaf 10 mites/plant0–1Alpha-cypermethrin 100 g/L 50–100 mL; bifenthrin 100 g/L 50–100 mL; omethoate 290 g/L 100 mL (watch SP / OP resistance)Emergence – 2 true leaves9 m / 13.8 m/s / 4 m / 30 L/ha / 320 µmT100
Blackleg (seedling foliar)Susceptible variety, high-risk paddock (BlacklegCM)0–1Prosaro 420 SC 375–450 mL (aerial ≥20 L/ha); Aviator Xpro 550–650 mL; Miravis Star 600–1000 mL4–6 leafAs aboveT100
Rosette – bud / (Jun–Aug)Grass weedsRyegrass 2 leaf – tillering1Clethodim 240 g/L 150–250 mL + adjuvant (aerial 20–30 L/ha)Before bud8 m / 9 m/s / 3.5 m / 30 L/ha / 500 µmT100
GPA / cabbage aphid≥20% of plants infested0–1Sulfoxaflor 240 g/L 100–200 mL; afidopyropen 100 g/L 50 mL; flonicamid 100 g (GPA highly resistant to SPs / carbamates)Bud – floweringInsecticide parametersT100
Flowering / (Aug–Sep)Sclerotinia + upper canopy blackleg20–30% bloom (14–20 flowers on the main stem) + rain forecast / wet canopy; not after 50%1 (2 in high-pressure zones)Prosaro 420 SC 375–450 mL (aerial ≥20 L/ha, 30 recommended); Aviator Xpro 550–800 mL (aerial ≥20 L/ha, MEDIUM); Miravis Star 750–1000 mL; procymidone 500 1 LBBCH 63 (optional BBCH 65, rotate groups)9 m / 13.8 m/s / 4 m / 30 L/ha / 320 µmT100
Podding / (Sep–Oct)DBM / native budwormDBM >50–100 per 10 sweeps; budworm ≈4 per 10 sweeps1Emamectin 17 g/L (Affirm) 150–300 mL (aerial ≥20 L/ha, ≤2 per season); spinetoram 150 mL; Bt; NPV (Vivus) 100–375 mL; alpha-cypermethrin 200–300 mL (budworm only)End of flowering – podding; mind the WHP to windrowingAs aboveT100
Ripening / (Oct–Nov)Desiccation (instead of windrowing)70% of pods yellow; seed brown / blue and pliable1Diquat 200 g/L 1.5–3 L + Agral 200 mL/100 L (aerial 30–60 L/ha; 4-day WHP) [follow the APVMA 2026 label]≈70% seed colour change; direct head 4–7 days later8 m / 9 m/s / 3.5 m / 30 L/ha / 500 µmT100
Snail baits (post-harvest / pre-sowing)White snail 5/m², conical snail 20/m²1Metaldehyde 50 g/kg 5–7.5 kg/ha; iron-based baits 5–16 kg/haAutumn, before egg layingSpreader 6–8 m / 8–10 m/sT100 spreader

Sources: DPIRD registered canola fungicides 2024–25; DPIRD insecticide guide 2024; Bayer Prosaro / Aviator Xpro labels; APVMA Affirm / clethodim / Reglone labels; cesar; CropLife 2026 RMS. Rates are label ranges — always follow the current APVMA label and agronomist advice.

3.5 DJI T100 application parameters for canolaSource slide 22
Historical source material: these flight settings and chemical references reproduce the October 2026 research. They are not current instructions. Verify aircraft approvals, product labels, operating conditions and regulations for each job.
Four indicative programme profiles from source slide 22
Source profileSwathSpeedHeightVolumeDropletStated objective
Fungicide9 m13.8 m/s4 m (above canopy)30 L/ha320 µmcarry the spray through the flowering canopy to the main stem and branch bases (where sclerotinia infects); Prosaro label recommends 30 L/ha by air; avoid peak bee activity
Insecticide9 m13.8 m/s4 m (above canopy)30 L/ha320 µmDBM / budworm larvae inside the podding canopy; fly in the evening; Affirm aerial ≥20 L/ha; mind the withholding period to windrowing / harvest
Herbicide8 m9 m/s3.5 m30 L/ha500 µmclethodim grass control and fallow knockdowns; VERY COARSE droplets meet glyphosate / 2,4-D drift requirements; atrazine and Intervix must not be applied by air
Desiccant (diquat)8 m9 m/s3.5 m30 L/ha500 µma contact product needs whole-canopy coverage; 30 L/ha is the Reglone aerial label minimum; avoid inversions and high temperatures; direct head 4–7 days later
T100 hardware figures quoted in the source
T100 key specifications (Australia)Value
Max take-off weight / payload175 kg / 100 L or 100 kg full load (CASA specific exemption)
Spray tank / spreader hopper100 L / 150 L
Max flow rate30 L/min (two nozzles) / 40 L/min (four nozzles)
Effective swath / droplet range5–13 m / 50–500 µm
Battery DB216041 Ah 52 V, 8–9 min to 95%; three batteries + one charger kit
Actual work rate @30 L/ha22–26 ha/h (3.3 ha per sortie); 180–260 ha per day

Sources: EE Group application parameters; DJI T100 specifications; Bayer / Syngenta label aerial directions.

3.6 T100 spraying and desiccation workflow (five standard steps)Source slide 23
Historical source material: chemical names, rates, withholding periods, flight settings and licensing statements reproduce the supplied October 2026 presentation. They are not instructions or confirmation of current legal permissions. Check the current registered label, APVMA decisions, CASA approvals and state requirements before any operation.

01 Pre-flight checks

Aircraft, airspace and conditions

Check batteries, radar, nozzles and RTK unloaded; confirm the label's aerial directions, wind 3–15 km/h and no inversion; manned ag aircraft are busy at flowering — broadcast on CTAF and coordinate airspace with local AAAA operators; check for powerlines and trees within 30 m

02 Paddock mapping

Survey flight and AI recognition

Mark the boundary with the aircraft or controller; AI picks up boundaries, trees, poles, water bodies and beehive sites; set water-body buffers (Prosaro aerial 60–180 m) and a 150 m buffer from dwellings

03 Route planning

Along tramlines / windrowing direction

Plan back-and-forth runs along the tramlines or windrowing direction; fungicide / insecticide 9 m spacing at 4 m; herbicide / desiccant 8 m at 3.5 m; 1–1.5 m boundary inset; return-to-home 10 m above the tallest obstacle

04 Parameter set-up

Fine-tuned by product type

Fungicide / insecticide 13.8 m/s, 30 L/ha, 320 µm; herbicide / desiccant 9 m/s, 30 L/ha, 500 µm; put water-sensitive paper mid-stem on the first sortie and check deposition before running the block

05 Autonomous operation

Hands-off flight control

Confirm RTK fix and a safe launch site; one-touch take-off, auto-resume spraying, auto return on low battery or empty tank; mixing station and generator cycle in step; stage desiccation by the area that can be harvested 4–7 days later

Core value: a standard five-step workflow solves the problem of a tall, brittle crop in a wet paddock at flowering; RTK positioning with no overlap or misses, 180–260 ha per unit per day, launched from the headland — zero ground passes, zero shed pods.

3.7 T100 pre-harvest desiccation: the core alternative to windrowingSource slide 24
Historical source material: chemical names, rates, withholding periods, flight settings and licensing statements reproduce the supplied October 2026 presentation. They are not instructions or confirmation of current legal permissions. Check the current registered label, APVMA decisions, CASA approvals and state requirements before any operation.

Ripening canola (EE Group, NSW)

Original data: source slide 24
OptionTiming and operationCost ($/ha)AdvantagesDrawbacks / risks
Windrowing60–80% seed colour change (mid main stem + branches); cured in the windrow 10–14 days then picked up30–50 (contract) + 95 pick-up harvestTraditional; even drying; weed controlWindrowing too early costs ≤100 kg/ha per day ($50/ha/day); hard to time across a big area; the windrower drives through the crop
Direct headingSeed moisture 6–8%, 10–14 days after the ideal windrowing date58 (harvest)Saves $37/ha; works well with shatter-tolerant types (PodGuard)Shattering risk (modelled 25%); heavy losses in wind or storms; longer harvest
Drone desiccation70% of pods yellow / ≈70% colour change; diquat 1.5–3 L/ha at 30 L/ha; direct head 4–7 days later30–40 (T100 service) + 58 (harvest)No ground pass, no shed pods; harvest ≈5 days earlier; staged precisely; ryegrass seed set −65–87%Label WHP (4 days; 14 days for crop-topping under the new decision); needs near-full coverage; APVMA 2026 rate cap to confirm

Desiccation economics (2 t/ha, $800/t)

$30–40/ha

Drone desiccation service price

$30–50/ha

Windrowing contract (replaced)

$37/ha

Harvest saving, direct heading vs pick-up

$50/ha/day

Loss per day from windrowing too early

≈5 days

Harvest brought forward by desiccation

0 passes

Ground / windrower passes through the crop

Key point: drone desiccation turns "windrow + pick-up" ($30–50 + $95/ha) into "desiccate + direct head" ($30–40 + $58/ha), saving $37–57/ha while removing the windrower's wheel damage and the timing risk; The Land (Dec 2025) lists desiccating canola and pulses and spraying mature crops without knocking pods as a main reason Australian farms buy spray drones. The diquat aerial label is 30–60 L/ha; the APVMA decision of 23 June 2026 caps diquat at 231 g a.i./ha per application with a 14-day crop-topping WHP — check the new label before every job.

Sources: GRDC direct-heading canola fact sheet; GRDC Update 2021 (windrowing timing); GRDC GroundCover; Syngenta Reglone label; APVMA (23 Jun 2026); The Land (Dec 2025).

3.8 Compliance requirements for drone spraying in AustraliaSource slide 25
Historical source material: chemical names, rates, withholding periods, flight settings and licensing statements reproduce the supplied October 2026 presentation. They are not instructions or confirmation of current legal permissions. Check the current registered label, APVMA decisions, CASA approvals and state requirements before any operation.

CASA aviation rules

  • T100 (>25 kg): RePL with class / type rating, even on your own land
  • Commercial work (for hire): ReOC operator's certificate + registration
  • One pilot per aircraft, VLOS; EVLOS / BVLOS need separate approval
  • T100 MTOW 175 kg: CASA specific exemption obtained — full 100 L / 100 kg load permitted
  • Manned ag aircraft are busy over canola at flowering: the AAAA issued a near-miss safety warning in Sept 2026 — broadcast on CTAF (AROC) and coordinate with local operators before every job

APVMA chemical labels

  • Drone application = aerial application: the label must carry aerial directions
  • Confirmed aerial labels for canola: Prosaro (≥20 L/ha, MEDIUM, 60–180 m water buffers), Aviator Xpro (≥20 L/ha), Affirm (≥20 L/ha), clethodim (20–30 L/ha), Reglone (30–60 L/ha)
  • No aerial use: atrazine (TT canola), Intervix (ground only), pre-emergent herbicides
  • Diquat / paraquat decision of 23 June 2026: 231 g a.i./ha cap, 14-day crop-topping WHP, closed mixing
  • No sclerotinia fungicide after 50% bloom (MRL); pod-stage insecticide WHPs count to the windrowing date

State chemical licences

  • NSW EPA: RPA pesticide control licence (pilot, needs RePL) + RPA pesticide business licence (needs ReOC); AQF3 ChemCert; no spraying within 150 m of dwellings / schools; records within 24 h, kept 3 years
  • VIC: RPA agricultural aerial operator licence ($967.10 / 3 yrs) + pilot chemical rating licence ($388.55 / 3 yrs); daylight only; wind 3–13 km/h; fully autonomous flight prohibited
  • SA: PIRSA chemical best practice + commercial operator licence
  • Bees: notify beekeepers within 2 km before flowering sprays and avoid peak bee activity (label bee warnings)

① CASA RePL

25 kg class rating · 5-day course

›

② CASA ReOC + AROC

Operator's certificate · radio

›

③ State chemical licence

NSW EPA RPA licences / VIC AAOL + PCRL

›

④ ChemCert AQF3

AHCCHM304/307 chemical safety

EE Group recommendation: dealers and contractors should treat "RePL + ReOC + state chemical licence + ChemCert" as the entry standard; application records (time, rate, location) are kept automatically by the DJI platform, meeting the NSW EPA three-year requirement; share flowering-season job plans with local fixed-wing operators.

Sources: CASA; APVMA RPAS application policy and decision of 23 Jun 2026; Bayer / Syngenta / APVMA labels; NSW EPA; Agriculture Victoria; PIRSA; AgAir Update (Sep 2026).

3.9 In the paddock: T100 on NSW canola at full bloom (September 2026)Source slide 26

T100 flying the tramlines (video frame)

Canola at full bloom, wheel tracks clearly visible

Canola crop at full bloom

Flowering heads and pods — the parts ground gear knocks off

Battery swap in the paddock (three batteries, one charger)

Ute-mounted generator and charging station

Job summary: fungicide / insecticide application on canola at full bloom, single T100, 9 m × 13.8 m/s × 4 m, 30 L/ha, 320 µm; flown along the existing boom tramlines and launched from the headland track — no ground pass through the crop. [Location, area, time taken and grower feedback to be added by EE Group]

3.10 Work-rate comparison: T100 vs boom spray vs fixed-wingSource slide 27
Interpretation: any projected benefits, costs, comparisons, service rates or market sizes in this subsection are research examples or EE Group assumptions, not independently measured results from the NSW photographed paddock.
Original data: source slide 27
DimensionDJI T100 droneSelf-propelled boom (36 m)Fixed-wing ag aircraftDrone verdict
Area per unit per day180–260 ha/day (spreading can extend into the night)≈500 ha/day (36 ha per boom hour)1,000+ ha/day (large paddocks)In between, but not limited by ground access
Hourly rate @30 L/ha22–26 ha/h (actual)30–36 ha/h (≈50% after refilling and moves)60–100 ha/h—
Load per sortie / fill100 L / 100 kg (CASA specific exemption)4,000–6,000 L1,000–3,000 LFrequent refills — mixing-station model
Re-entry after rain≤2 hours (never touches the ground)3–7 days (longer on clays)Same day (needs a usable strip)★ Saves the 7–10 day sclerotinia window
Crop damage at flowering / ripeningNoneTracks 2.1–2.8% + snapped branches and shed pods, 1–4% whole-paddock lossNone★ Saves $16–64/ha
Paddock suitabilityAny size or shape; precise buffers around hives and waterBest on big paddocks; limited in wet low spots and irrigation baysNeeds a ≥1,000 m strip, large areas, minimum orders; queues nationwide at flowering★ Small paddocks and staged desiccation
Service price$15–25/ha; desiccation $30–40/ha$8–13/ha (contract); windrowing $30–50/ha$20–25/ha (EE Group market); published $13–35/haOn a par with aircraft, a little above the boom
Capital cost≈$45,000 (three batteries + charger) + generator $5,190$600,000–800,000; windrower extraAircraft >$1 m, contractors only★ Within reach of a farm

Sources: DJI; The Land (Dec 2025); GRDC / Farmanco machinery investment guide (2021); GroundCover (Nov 2024); NSW DPI canola budgets; EE Group market prices.

3.11 Three application modes: where each fitsSource slide 28
Interpretation: any projected benefits, costs, comparisons, service rates or market sizes in this subsection are research examples or EE Group assumptions, not independently measured results from the NSW photographed paddock.
Original data: source slide 28
DimensionDJI T100 droneSelf-propelled boomFixed-wing ag aircraftDrone verdict
Mode of operationFully autonomous RTK routes + terrain followingDriven (partly auto-steer)Piloted, visualFully autonomous, frees up labour
Growth stagesWhole season (biggest edge after flowering)Best seedling to bud; snaps branches and sheds pods after floweringWhole seasonThe only "whole-season, no-damage" option
Access in wet paddocks✅ Not limited by soil moisture❌ Can't get on for 3–7 days after rain; bogs and ruts✅ But needs a strip and a minimum areaSolves "can't get on"
Pre-harvest desiccation✅ $30–40/ha, staged precisely, no shed pods⚠️ Possible but 2–4% wheel damage; most farms windrow instead✅ 30–60 L/ha on large areasBest alternative to windrowing
PrecisionRTK ±10 cm; no overlap or misses; boundary / hive buffersMature section and nozzle controlMost drift, strictest buffersLeads on precision and penetration
AvailabilityFarm-owned or local contractor; ≈3,000 ag drones operating in Australia (2026)Most farms own one≈130 operators, 300-odd aircraft; booked out at floweringFills the capacity gap in wet seasons and at flowering

Positioning: the boom does the pre-sowing and seedling jobs on dry ground, fixed-wing covers very large emergency areas, and the T100 takes the flowering fungicide, pod-stage insecticide, pre-harvest desiccation and wet / small-paddock work — three of the four passes in a canola season, and the three worth the most. For a farm, one T100 (≈A$50,000) removes the 1–4% loss from every ground pass after flowering and replaces windrowing.

Sources: AAAA; The Land (Dec 2025); CASA; GRDC; EE Group.

Value and performance scenarios

4.1 Yield losses from canola diseases and pests in AustraliaSource slide 30
Interpretation: any projected benefits, costs, comparisons, service rates or market sizes in this subsection are research examples or EE Group assumptions, not independently measured results from the NSW photographed paddock.
Original data: source slide 30
Pest / diseaseScale of lossPer hectare / proportionMaximum loss potentialSource
SclerotiniaWA 2013 >A$59 mSevere paddocks 0.5–1 t/haVIC 24% recorded, WA >20%; each 1% incidence ≈ 23 kg/haGRDC 2014/2017; Ag Vic; DPIRD
Blackleg (crown)>90% loss uncontrolledResistant varieties avoid ≈20% loss ≈ $68.75/ha/yrYield lost once >30% of the crown is discoloured; DMI resistance in 30% of isolatesGRDC blackleg case study; GRDC 2021
Upper canopy blackleg (UCI)—Up to 30% + 20% from podsEarly flowering + rain at floweringGRDC GroundCover; GRDC 2019
Diamondback mothA third of WA canola affected in a bad year—Buds and young pods eaten; SP / OP resistance widespreadGrain Central; cesar
Native budworm—Each larva per 10 sweeps ≈ 6 kg/haBores into pods at podding; control needed one year in threecesar ET; NSW DPI budget
Aphids / TuYV—Colonies on heads reduce pod setGPA spreads turnip yellows virus; neonicotinoid resistance widespreadGRDC GroundCover 2024/25
Redlegged earth mite>10% of canola failures mite-related—Seedling loss and resowingAOF Canola Manual
Windrowing too early≤100 kg/ha per day$50/ha/dayNSW trials lost up to 32–55%; Coonamble +8 days = +500 kg/haGRDC 2021; GroundCover
Shattering (delayed harvest)—10 pods/m² ≈ 10 kg/haNon-shatter-tolerant types lose another 500 kg/ha with a 14-day delayGRDC direct-heading fact sheet

Key points

  • At ≈$820/t, every 1% of canola yield ≈ $16–20/ha — the same percentage loss costs more than twice as much as in wheat
  • The only control window for both sclerotinia and UCI blackleg is 20–30% bloom, which coincides with winter–spring rain
  • Harvest management (windrowing timing, shattering) is a loss source unique to canola — desiccation is the drone's direct entry point

Sources: GRDC Update (2014/2017/2019/2021); Agriculture Victoria; DPIRD; cesar Australia; GRDC GroundCover; AOF; Grain Central.

4.2 The value of timeliness: flowering and harvest windows quantifiedSource slide 31
Interpretation: any projected benefits, costs, comparisons, service rates or market sizes in this subsection are research examples or EE Group assumptions, not independently measured results from the NSW photographed paddock.

+20%

Average yield response to a sclerotinia fungicide across 25 Bayer trials (Prosaro 375 mL/ha)

Bayer 2011–13

$245/ha

Return from aerial application at 35 L/ha and 30% bloom at Cowra NSW (2.18 → 2.75 t/ha)

Bayer product guide

7–10 days

Economic sclerotinia window (20–30% bloom); prohibited after 50% bloom

DPIRD / CropLife

$118–148/ha

Net return from one / two sprays in WA 2016 (chemical $33 + application $7/ha)

GRDC 2017

$50/ha/day

Loss per day from windrowing too early; avoided by staged desiccation

GRDC 2021

$37–57/ha

Saving per hectare, desiccate + direct head vs windrow + pick-up

GRDC fact sheet; EE Group

Original data: source slide 31
JobCause of delay (ground gear)Cost of delayDrone response
Sclerotinia / UCI at 20–30% bloomAugust rain; 1–1.5 m crop snaps; aircraft booked out at floweringMissed window = no control; 0.4 t/ha ≈ $320/ha in a high-pressure yearAirborne ≤2 h after rain; two units cover 3,000+ ha in 7 days
DBM / budworm (podding)Crop at full height, pods shed easily; spring rainEach budworm per 10 sweeps ≈ 6 kg/ha; DBM can strip young podsEvening / night work, no wheel damage
Pre-harvest desiccationWindrower drives through the crop; hard to time across the areaEarly windrowing $50/ha/day; shattering 10 kg/ha per 10 pods/m²Staged by the area harvestable in 4–7 days, $30–40/ha
Seedling mites / blackleg (4–6 leaf)Autumn rain after sowing, wet claysSeedling loss and resowing; crown infectionFlies straight after rain, 30 L/ha

Sources: Bayer Prosaro canola guide; GRDC Update (2014/2017/2021); DPIRD; CropLife 2026 RMS; cesar; GRDC direct-heading fact sheet.

4.3 Avoiding wheel damage and compaction at flowering and ripeningSource slide 32
Interpretation: any projected benefits, costs, comparisons, service rates or market sizes in this subsection are research examples or EE Group assumptions, not independently measured results from the NSW photographed paddock.
Original data: source slide 32
Scenario (per ha)Boom passT100 passDrone saving
Application cost$8–13$15–25−$7 to −$12
Wheel damage from one flowering pass (1–3%)$16–48 (2 t/ha)$0+$16 to +$48
Delay loss after rain (high-pressure sclerotinia year, 30% weighted)≈$96$0+$96
Long-term compaction (sand / clay, amortised)$5–15$0+$5 to +$15
Total (one flowering fungicide pass)$125–172$15–25+$100 to +$157/ha

Reading the numbers

  • Canola is high value: wheel damage alone is worth 1–4 times the drone's application fee
  • Counting "delay = no control" for sclerotinia, the drone's net advantage on one flowering pass in a wet year is $100–157/ha
  • Desiccating with ground gear loses 2–4% to tracks and shed pods ($32–64/ha) — that alone covers the $30–40/ha drone fee
  • Growers report ≈+5% yield from drone use in wet years (The Land 2025, not trial-verified)

Note: losses are EE Group scenario estimates based on GRDC / BCG CTF research and overseas wheel-track data; delay loss weighted at a 30% probability × $320/ha.

4.4 Emergency response at flowering: efficiency comparedSource slide 33
Interpretation: any projected benefits, costs, comparisons, service rates or market sizes in this subsection are research examples or EE Group assumptions, not independently measured results from the NSW photographed paddock.
Original data: source slide 33
DimensionT100 drones (fleet of 2)Self-propelled boomFixed-wing aircraftVerdict
Productive hours per day8–10 h (spreading to 12 h at night)6–8 h (humidity, inversions, ground access)6–8 h (after sunrise, before the inversion)Drone +25%
Area per unit per day180–260 ha (T100, canola at full bloom); 2 units 360–520 ha≈500 ha (dry ground); 0 when wet1,000+ ha (needs a strip; booked out at flowering)In a wet year the drone works, the boom does nothing
Area covered in the 7–10 day sclerotinia window2,500–3,600 ha (2 units)0–5,000 ha (depends on soil moisture)Depends on the queueDrone is the most certain after rain
Response time to an outbreak≤2 h (pilot + mixing station)≥24 h (waiting to get on) or not at all≥24–72 h (order queue, 2021/22 wet years)Wins back ≥22 h of the window
Refill / relocation (each)≤3 min (battery + chemical, RTK retained)20–30 min (water, chemical, clean-out)15–20 min (return to strip)Drone turnaround ×5
Spraying ahead of rain (2 h)44–52 ha (one unit)60–70 ha (if it can get on)120+ ha (if a slot exists)Drone does not depend on ground access

Summary: the logic of sclerotinia control is "if rain is forecast, get the fungicide on before 20–30% bloom" — and the days rain is forecast are exactly when the boom can't get on and fixed-wing is booked out nationwide. Drone timeliness makes "getting it on" a certainty; contractors should have crews, pre-mixed product and airspace coordination in place before mid-August.

Sources: DJI; DPIRD; Grain Central (2021/2022); AAAA; EE Group operating experience. Response times and areas are typical-scenario estimates.

4.5 How the drone lifts canola returns (grower view, per hectare)Source slide 34
Interpretation: any projected benefits, costs, comparisons, service rates or market sizes in this subsection are research examples or EE Group assumptions, not independently measured results from the NSW photographed paddock.
Original data: source slide 34
BenefitConventional ground / aircraftT100 droneSaving / gainNotes
Yield responseBase yieldTimely sclerotinia / UCI spray +8–20% (0.16–0.4 t/ha)+$130–320/haBayer 25-trial average +20%; WA 2016 main effect +8%
Wheel damage avoided1–4% loss per pass after floweringNo snapped branches, no shed pods, no compaction+$16–64/ha per pass36 m boom tracks 2.1–2.8% + damage either side
Desiccation instead of windrowingWindrow $30–50 + pick-up $95/haDesiccate $30–40 + direct head $58/ha+$37–57/haAlso avoids early-windrowing losses of $50/ha/day
Application costGround $8–13/ha; aircraft $20–25/ha$15–25/ha$0 to +$10/ha vs aircraftSame as or below fixed-wing, no minimum order or strip
Pod-stage pestsCrop at full height, hard to get onEvening work, Affirm / NPV by airAvoids 6 kg/ha per budwormDBM resistance management (Group 6/5/11 rotation)
CapitalSelf-propelled boom $600–800k + windrowerT100 ≈ $50kCapex −90%Farm-owned, or through a local contractor
Combined benefit per ha (key passes, wet year)——≈ +$60–120/ha per passThree key passes in a season ≈ +$180–360/ha

★ NSW scenario at 2.0 t/ha and $800/t: taking on three key passes in a season (flowering fungicide, pod-stage insecticide, pre-harvest desiccation), the drone returns the grower roughly $180–360/ha — 25–45% of the canola gross margin (≈$790/ha). These figures are scenario estimates based on GRDC / Bayer trials and EE Group market parameters and should be calibrated continuously against actual job data.

Costs, operator economics and market sizing

5.1 Grower view: NSW dryland canola gross margin per hectareSource slide 36
Interpretation: any projected benefits, costs, comparisons, service rates or market sizes in this subsection are research examples or EE Group assumptions, not independently measured results from the NSW photographed paddock.
Original data: source slide 36
ItemQtyUnit priceAmount ($/ha)Notes
CostsHybrid seed2.5 kg$28/kg70TT / CL / RR hybrid; open-pollinated TT ≈ $25
Seed treatment1$1515Blackleg + mite dressing
MAP / DAP at sowing70 kg$1.30/kg91
Urea topdressing150 kg$1.50/kg225≈80 kg N per tonne of target yield
Herbicides (fallow + pre-em + post-em)4 passes—90Glyphosate / trifluralin / atrazine / clethodim
Fungicides1–2 passes—48In-furrow flutriafol 15 + flowering Prosaro 33
Insecticides1–2 passes—25Mites + pod-stage budworm / DBM
Spraying (5 passes)5$8–1350Own boom $6–11 per pass
Spreading1$8.509Ground spreader
Windrowing or desiccation1$30–5035Windrowing contract; desiccation $30–40
Fuel, repairs (sowing / harvest)——55Own machinery
Freight2.0 t$25/t50To port / crusher
Levies + EPR + insurance——45GRDC 0.99% + state levy + hail cover
Total variable costs808
IncomeCanola seed2.0 t$800/t1,600NSW avg ≈1.9 t/ha; Sep east-coast price $818/t
Gross margin792Break-even $404/t or 1.0 t/ha

Key points

  • The canola gross margin is about twice wheat's (≈$790 vs $380/ha), but inputs are higher too ($808 vs $670/ha) and more sensitive to the timing of nitrogen and fungicide
  • GRDC / SAGIT 2022 guide: medium-rainfall canola GM $241 (TT) to $384 (conventional)/ha; 2026 prices are at a two-year high ($818–875/t)
  • The wheel-damage or delay loss from one flowering pass ($100–157/ha) is 13–20% of the gross margin

Sources: GRDC / SAGIT Farm Gross Margin Guide (2022) structure; NSW DPI canola budgets (structure); ABARES 2025-26 yields; Grain Central prices (Sep 2026); EE Group compilation.

5.2 Grower view: "full cost" of the three application methodsSource slide 37
Interpretation: any projected benefits, costs, comparisons, service rates or market sizes in this subsection are research examples or EE Group assumptions, not independently measured results from the NSW photographed paddock.
Original data: source slide 37
Cost / benefit item ($/ha, 2 t/ha, $800/t)Self-propelled boomFixed-wing aircraftDJI T100
Application fees (flowering fungicide + desiccation)16–2645–5545–65
Wheel damage at flowering (1–3%)16–4800
Wheel damage + shed pods at desiccation (2–4%)32–6400
Long-term compaction (amortised)10–3000
Delay loss after rain (sclerotinia, probability-weighted)≈96≈48 (queue)0
Airstrip / minimum order / ferry surcharge00–100
Total cost170–26493–11345–65
Difference vs T100+125 to +199+48—

Conclusions

  • On application fees alone the drone costs $29–39/ha more than the boom; once snapped branches at flowering, shed pods at desiccation, compaction and delay are counted, the boom's true cost in a wet year is $125–199/ha higher
  • Against fixed-wing: the same price, but no airstrip, minimum order or flowering-season queue; staged desiccation, small paddocks and irrigation bays are clear advantages
  • Pre-sowing and seedling jobs on dry ground remain cheapest by boom — the drone's place is the three passes after flowering where "getting on costs money"

Note: boom fee at contract rate $8–13/ha; delay loss at 30% probability × $320/ha; fixed-wing queue delay discounted 50%. All scenario estimates.

5.3 Operator view: T100 investment and payback (canola)Source slide 38
Interpretation: any projected benefits, costs, comparisons, service rates or market sizes in this subsection are research examples or EE Group assumptions, not independently measured results from the NSW photographed paddock.
Original data: source slide 38
ItemAmount (A$)Notes
T100 aircraft (three batteries + one charger kit)45,000EE Group 2026 price (incl. 3 × DB2160, charger, controller)
D14000iE generator5,190One unit
RTK base / mixing station / tank and pump / trailer≈5,000Estimate
RePL + ReOC + state chemical licence + ChemCert≈4,000One-off, including training
Initial investment≈59,000
Annual fixed costs≈15,400Depreciation over 4 yrs (residual $10k) ≈12,000 + insurance 1,400 + maintenance 2,000
Variable cost per ha≈4.1Pilot + mixer 2 × $45/h ÷ 24 ha/h ≈ 3.75 + fuel 0.35
Blended canola service price≈$25/haWeighted: fungicide / insecticide $15–25 + desiccation $30–40

≈740 ha

Annual break-even area (at $25/ha); farms under 2,000 ha take >1 year to pay back

5,000 ha

Net profit ≈ A$89k a year investment recovered in <1 year

19–28 days

Working days to reach 5,000 ha (180–260 ha/day)

10,000 ha

Net profit ≈ A$194k a year achievable with canola + wheat across seasons

Note: net profit = area × (25 − 4.1) − 15,400. Canola flowering (Aug–Sep) and desiccation (Oct–Nov) complement the wheat stem elongation – grain fill windows, so one T100 can be scheduled across both crops. Insurance and maintenance per EE Group.

5.4 Market size: drone services and fleet demand for Australian canolaSource slide 39
Interpretation: any projected benefits, costs, comparisons, service rates or market sizes in this subsection are research examples or EE Group assumptions, not independently measured results from the NSW photographed paddock.

3.70 M ha

Australian canola area 2025-26

ABARES Jun 2026

1.74 M ha

NSW + VIC + SA combined

NSW 0.95 / VIC 0.54 / SA 0.25

4 passes

Spray passes per canola season (herbicide 1, insecticide 1, flowering fungicide 1, desiccation 1)

EE Group

3,000 units

Ag drones operating in Australia (2026) ≈600 sold in 2025; 70% contractor-owned

EE Group 2026

Original data: source slide 39
MeasureAustraliaNSW + VIC + SALogic
Canola area (M ha)3.701.74ABARES 2025-26
Drone-suitable passes (M ha·passes / yr)14.86.96× 4 passes per season
5% penetration → area served (M ha·passes)0.740.35Near-term target
10% penetration → area served (M ha·passes)1.480.70Medium-term target
Service revenue @ $25/ha (5% / 10%)A$18.5 m / 37 mA$8.7 m / 17.4 mIncludes desiccation ($30–40/ha)
T100 units needed (5,000 ha per unit per yr)148 / 29670 / 139Professional contractors
T100 units needed (2,000 ha per unit per yr)370 / 740174 / 348Mainly farm-owned

Market view

  • 10% penetration on canola is a service market of ≈A$37 m a year and 300–740 T100-class units; stacked with wheat (A$74 m), the same fleet works across crops from August to November with much higher utilisation
  • Desiccation is the fastest-growing drone demand on canola (The Land 2025 lists it among the main reasons farms buy), and it fits the APVMA 2026 push for closed mixing and the end of knapsack use
  • Of the ≈3,000 ag drones in the country, 70% are contractor-owned; penetration of T100-class heavy-lift units at canola flowering and desiccation is still early

Sources: ABARES Australian Crop Report (Jun/Sep 2026); EE Group 2026 market data (fleet, sales, ownership); The Land (Dec 2025); APVMA; EE Group assumptions (penetration, annual area per unit).

View additional disease, pest and weed reference images — Part 1 of 26 reference photographs from the study presentation
Illustrative disease reference photograph extracted from source slide 18, image 9
Illustrative disease photograph, source slide 18.
Illustrative disease reference photograph extracted from source slide 18, image 10
Illustrative disease photograph, source slide 18.
Illustrative disease reference photograph extracted from source slide 18, image 11
Illustrative disease photograph, source slide 18.
Illustrative insect pest reference photograph extracted from source slide 19, image 5
Illustrative insect pest photograph, source slide 19.
Illustrative insect pest reference photograph extracted from source slide 19, image 6
Illustrative insect pest photograph, source slide 19.
Illustrative insect pest reference photograph extracted from source slide 19, image 8
Illustrative insect pest photograph, source slide 19.
View additional disease, pest and weed reference images — Part 2 of 26 reference photographs from the study presentation
Illustrative insect pest reference photograph extracted from source slide 19, image 10
Illustrative insect pest photograph, source slide 19.
Illustrative insect pest reference photograph extracted from source slide 19, image 11
Illustrative insect pest photograph, source slide 19.
Illustrative weed reference photograph extracted from source slide 20, image 6
Illustrative weed photograph, source slide 20.
Illustrative weed reference photograph extracted from source slide 20, image 8
Illustrative weed photograph, source slide 20.
Illustrative weed reference photograph extracted from source slide 20, image 9
Illustrative weed photograph, source slide 20.
Illustrative weed reference photograph extracted from source slide 20, image 10
Illustrative weed photograph, source slide 20.

Reference photographs from the source presentation include canola pests and diseases and related brassica species. Original credits are listed on the relevant slides.

Reference framework

Original source: Lucas Jiao, EE Group Pty Ltd, Australian Canola Industry Survey and DJI Agras T100 Whole-Season Application Solution, 15 October 2026. The presentation cites ABARES, ABS, GRDC, Agriculture Victoria, NSW DPI, PIRSA, DPIRD, CropLife, Bayer, Syngenta, APVMA, CASA and other industry publications. The following authoritative references were also checked for the 2026 context:

Field photographs and reference illustrations are reproduced from the presentation. Credits for third-party images appear on slides 10 and 18-20; some crop-health reference images show related brassica species.

EE Group Australia

More on agricultural drone applications

Explore the DJI Agriculture range, review the Agras T100 product information or browse other practical applications. EE Group works through its authorised Australian distribution network and does not sell Agras aircraft directly to end customers.

NSW field photographs, September 2026 | Research and source presentation: Lucas Jiao, EE Group Pty Ltd, 15 October 2026.